Anyone who\u00b4s replaced a head gasket on an internal combustion engine knows a smooth, flat surface on both cylinder head and block is needed for proper operation. No one understands this better than automakers, who strive for predictable, controlled surface finishes and high production output, together with maximum tool life and the lowest tooling cost per machined component.<\/p>\n
Many machinists might think, \u00bbWhat\u00b4s the big deal? Aluminum is one of the easiest materials around.\u00bb And while that is certainly true of the ubiquitous 6061-T6, nothing could be further from the truth when it comes to the aluminum alloys used in automotive applications. Grades 319 and 390, for example, are readily cast into the complex shapes needed for engine blocks, pistons, heads, pulleys, and similar parts, but due to their high silicon content\u2014easily 20 to 30 times that of 6061\u2014they\u00b4re like cutting sand.<\/p>\n
Fortunately for those charged with machining these abrasive metals, there\u00b4s a better alternative than carbide cutting tools, one that produces mirror finishes and produces tens of thousands of parts per edge.<\/p>\n
\u00bbFinishes of 2 to 3 \u03bcm Ra are easily obtainable, as is tool life between indexing of 40,000 engine blocks, cylinder heads, and other automotive components,\u00bb says Tim Marshall, Senior Global Product Manager for Indexable Milling at Kennametal. \u00bbThis new face milling platform uses a fine-pitch aluminum body with wedge-style clamps and adjustable pockets. A variety of polycrystalline diamond (PCD) inserts are available, from mini-tips for light finishing cuts to full face wipers, standard cartridge inserts, and 1\/2 in. (12.7 mm) axial cutters for heavy roughing and shoulder cutting.\u00bb<\/p>\n
He\u00b4s talking about the KBDM PCD face milling system from Kennametal. Designed for high-volume machining, the KBDM is stocked in standard sizes of 2.5 – 8.0 in. (63 – 200 mm), although Marshall is quick to point out the company\u00b4s custom solution capabilities. \u00bbWe can offer cutters up to 21.5 in. (550 mm) in diameter. This allows customers to machine very large components in a single pass. We also have options for integral shank bodies, HSK mounting, left hand cutter rotation, as well as special edge preps and nose radii.\u00bb<\/p>\n
There\u00b4s more to the KBDM than a robust body design, however. Since automakers often create their own proprietary aluminum alloys, Kennametal has developed two PCD grades to complement it: KD1400 uses small diamond grains and offers excellent chipping resistance and good wear attributes, while KD1425 uses large diamond grains, giving it excellent abrasion resistance and thermal stability but only slightly lower performance where chipping is a concern. Both are capable of very high cutting parameters\u2014depending on the alloy and setup rigidity, Kennametal recommends an initial cutting speed of 3280 ft\/min (1000 m\/min) and feedrates of .004 in. per tooth (0.01 mm), although substantially higher values are possible.<\/p>\n
\u00bbA major machine builder conducted cutting tests for us against several competitive solutions,\u00bb Marshall says. \u00bbUsing a 24-tooth, 6.0 in. (150 mm) diameter face mill at 80% radial engagement and 0.04 in. axial DOC (1 mm), we ran at a feedrate of 0.006 in. IPT (0.15 mm) and 9600 ft\/min surface speed (2926 m\/min). This comes out to 6112 rpm, with a table feed of 880 IPM (22,350 mm). It was really moving. Even so, the KBDM produced a 14.7 Ra surface finish, several points better than the other cutting tools.\u00bb<\/p>\n
Marshall recommends presetting the KBDM offline using an optical or video style presetter. A small amount of lubricant should be applied to the adjustment and locking screws, and also the wedge side of the pocket. Turn the axial adjustment screw until the insert is 0.0004 – 0.0006 in. (0.010 – 0.015 mm) below the final set height, tighten the locking screws to 31 in\/lb. (3.5 Nm)\u2014don\u00b4t overtighten\u2014then adjust each insert to its final height position. If using a wiper insert, set it 0.0006 – 0.0008 in. (0.015 – 0.020 mm) higher than the rest.<\/p>\n
\u00bbIt\u00b4s simple to set up,\u00bb Marshall says. \u00bbYou can easily get everything within a couple microns. That’s one of the keys to successful face milling, not only for proper balance at high spindle speeds but also for achieving the desired surface finish\u2014when you’re finishing a deck face on a block or head, both are critical.\u00bb<\/p>\n
Adjusting the KBDM is a straightforward process\u2014use an optical presetting device whenever possible, and DON\u00b4T OVERTIGHTEN!<\/p>\n
KBDM PCD inserts are available in a variety of sizes. Here, a mini-tip suitable for finishing cuts is shown.<\/p>\n
KBDM cutters are stocked in standard sizes of 2.5 – 8.0 in. (63 – 200 mm), although specials up to 21.5 in. (550 mm) in diameter are possible.<\/p>\n","protected":false},"excerpt":{"rendered":"
Anyone who\u00b4s replaced a head gasket on an internal combustion engine knows a smooth, flat surface on both cylinder head and block is needed for proper operation. No one understands this better than automakers, who strive for predictable, controlled surface finishes and high production output, together with maximum tool life and the lowest tooling cost […]<\/p>\n","protected":false},"author":1,"featured_media":9864,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[120,1],"tags":[842,973],"class_list":["post-9863","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-tool","category-uncategorized","tag-kennametal","tag-milling"],"_links":{"self":[{"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/posts\/9863","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/comments?post=9863"}],"version-history":[{"count":0,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/posts\/9863\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/media\/9864"}],"wp:attachment":[{"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/media?parent=9863"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/categories?post=9863"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/mfgtechupdate.com\/wp-json\/wp\/v2\/tags?post=9863"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}